[email protected]

Basic catalogue - Standards, dimensions and grades

Welded steel pipes for pressure purposes acc. to DIN EN 10217 16 17 Line pipes acc. to DIN EN ISO 3183 / DIN EN 10208 18 19 Precision steel pipes DIN EN 10305 / Steel pipes with threaded ends DIN EN 10255 20 21 Steel pipes seamless acc. to DIN EN 10216-1 to -4 dimensions and masses 22 23 Carbide Depot ANSI-ISO Cross-ReferenceANSI / ISO Conversion. Enter insert part number designation:(no spaces or dashes) (examples) (designation chart) * This Field Is Required*Only Letters. Numbers and Dashes Allowed. Equivalent part number designations are listed below:

DESIGN DRAWING STANDARDS

7.2 For future U.S. customary / metric conversion, refer to the NAAMS Metric Equivalent Charts #1 & #2. 8. DIMENSIONING AND TOLERANCING 8.1 Dimensioning and tolerancing practices shall be as defined and illustrated in ANSI Specification #Y14.3M - 1994. 8.2 A zero before the decimal point shall be used for a number less than 1.0 (Example 0.5). DIN / ISO / EN Crossover Chart - Fuller Fasteners95 rows · DIN 479-8.8 Square Head; Low Head Socket Cap Screws. DIN 6912-8.8 Bare Steel with DIN 2501 Flange face dimensions and drilling dimensions PDF:DIN 2501 Flange face dimensions and drilling dimensions . Flange dimensions and drilling to DIN 2501. DN = diameter nominal (size) A = flange . D2 = diameter of raised face . D1 = diameter of bolt circle . n = number of bolts d = diameter of bolt holes = not standardized.

Flange Comparsion Tables

Rating Dia. Face Iron Steel Circle of Size Size Table Dia. Dia. Bolts Metric Inch Notes:There may be rounding or conversion deviations, but these should not exceed ± 1.5mm. If the deviation exceeds this tolerance it will be marked with a letter and an explanation given in the footnote. Gear Diametral Pitch, Module Conversion Table Chart Gear Module:is the unit of size that indicates how big or small a gear is. It is the ratio of the reference diameter of the gear divided by the number of teeth. Module = (Reference Diameter) / (Number of Teeth) m = d / z. Diametric, module and circular pitches Conversion. Insert Designation Chart - provides ANSI and ISO ANSI Code No. Inscribed Circle Size:ISO Code No. (metric cutting edge length) by shape code letter of insert:decimal in. fractional in. C:D:R:S:T:V:W:0.5.0625" 1/16 :1.2 (5).15625" 5/32:S4:04 (4mm) 03 (3mm) 03 (3mm) 06 (6mm) 1.5 (6) .1875" 3/16:04 (4mm)

Material conversion (ASTM-KS-JIS-DIN)

Material Conversion (ASTM - KS - JIS - DIN) ST'D NUMBER Gr.50-30 D4101 SC 42 G 5101 SC 42 Gr.65-35 D4101 SC 46 G 5101 SC 46 Gr.70-36 D4101 SC 49 G 5101 SC 49 Gr.32510 D 4303 BMC 35 G 5702 FCMB 35 Gr.35018 D 4303 BMC 37 G 5702 FCMB 37 Cl.No. 20A-C D 4301 GC 15 G 5501 FC 15 Paper Sizes - ISO and ANSI Formats - ANSI BlogJan 05, 2018 · ANSI A was modeled off letter paper, while ANSI B comes in two forms:ledger and tabloid, at 11x17 and 17x11, respectively. The larger sizes on this system are ANSI C, ANSI D, and ANSI E. The ANSI paper sizes are somewhat similar to the ISO sizes, in that cutting the sheet in half would produce two sheets of the next smaller size. SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM SUBSTITUTE MATERIAL (JIS, BS, DIN ) FOR ASTM SPECIFICATION CONTENTS Section 1. Scope 2. Basis 3. Additional Requirements 4. Table 5. Table 1, Plates 6. Table 2, Pipes 7. Table 3, Tubes 8. Table 4, Forging Welded (Size NPS 16 and over) Material A 283 Gr A D G 3457 STPY400 3602 SAW410 --- 3601 SAW410 A 285 Gr

Sorting out ANSI ISO inserts - Ace Micromatic

The nose radius of an ANSI insert is based on 1/64 fraction increments. A TNMG-432 insert would have a 0.031 nose radius. The third number is 2 (2 x 1/64 = 1/32). The ISO system is a conversion from the ANSI system, in metric values. This conversion can be done by using the conversion ANSI to DIN Flange - Boiler and Pressure Vessel Jun 03, 2015 · The DIN / metric flanges are PN numbers where the pressure is in bar at ambient temperature e.g. 10, 16, 25, 50 bar. ASME has inch bolting and DIN has metric bolts. The PN20 you refer to is ISO 7005 where they tried to make a blend of both e.g. the series goes 10/16/ 20 /25/40/ 50 /63 etc. and all have metric bolts.